WEBINAR – Accelerate your electronic designs with defect-free production

Video hosted by YouTube: playing it here means accepting YouTube's cookies.

Watch on YouTube
Questions / Answers:

Question 1: What should we do if we want to bring fabrication back to France for sovereignty reasons? Are reindustrialization and redesign mandatory?

Asked by: Pascal L – 5 Sep 2025 10:10

Answer: Good question, Pascal. Critical products, such as defense, involve sovereignty stakes. National authorities must become aware of this and accept the consequences (price & lead times).

Answered by Christophe LOTZ – 5 Sep 2025 10:12


Question 2: How can design parameters be aligned across manufacturers when each of them uses its own design software?

Asked by: Clement B – 5 Sep 2025 10:13

Answer: answered live

Answered by Christophe LOTZ – 5 Sep 2025 10:17


Question 3: Despite footprint standardization, board manufacturers often recommend other footprints for DFM reasons, most of the time based on their own field experience

Asked by: Pascal L – 5 Sep 2025 10:13

Answer: Work is under way on the footprint question with IPC7351. A presentation is planned for January 2026 at an international conference in Prague.

Answered by Christophe LOTZ – 5 Sep 2025 10:19


Question 4: Will it be possible to have access to the presented slides after the meeting? Thank you

Asked by: Nathan R – 5 Sep 2025 10:13

Answer: Yes, the slides and the recording will be sent to you.

Answered by Sacha MARROT - AFNOR-CEF – 5 Sep 2025 10:15

Answer: The video will also be available on YouTube.

Answered by Grégoire Boulay – 5 Sep 2025 10:16


Question 5: Is the space sector concerned by this spec?

Asked by: Anonymous participant – 5 Sep 2025 10:17

Answer: The scope of the 2212 is not restricted. The space sector can absolutely use it.

Answered by Christophe LOTZ – 5 Sep 2025 10:18


Question 6: Do you have an approximate date for the release of the IEC PAS 2212, officially IEC-branded and downloadable from the IEC website or through the AFNOR Cobaz site?

Asked by: Jean-Philippe V – 5 Sep 2025 10:19

Answer: The IEC/PAS is approved, but the copyright transfer is still under discussion. This point should be settled within a few weeks. The legal solution has been identified between AFNOR and the IEC.

Answered by Christophe LOTZ – 5 Sep 2025 10:21


Question 7: Hello, my question is probably a bit off-topic, my apologies if that is a problem: where and how can one get trained in electronic board design? Or do a refresher. Thank you.

Asked by: Anonymous participant – 5 Sep 2025 10:20

Answer: Grégoire, who will be speaking shortly, offers courses. There are also Campus Esprit in Redon and WeNetwork in Angers.

Answered by Christophe LOTZ – 5 Sep 2025 10:21


Question 8: Hello, entering the 2212 into Allegro through the "Constraint Manager" is not easy, tedious even... Do you share my view? Is there an already-configured script for this tool?

Asked by: Tony C – 5 Sep 2025 10:27

Answer: Native integration of the 2212 into the Cadence tools is under way.

Answered by Christophe LOTZ – 5 Sep 2025 10:32


Question 9: Are there any French PCB manufacturers that do not yet have the know-how to achieve acceptable yields for routing classes 9 or 10?

Asked by: Pascal L – 5 Sep 2025 10:28

Answer: Indeed, not every manufacturer can produce everything. That is also the case in China, where I ran a benchmark in June. Classes 9 and 10 are technological limits.

Answered by Christophe LOTZ – 5 Sep 2025 10:35


Question 10: How does the AFNOR Spec take into account the different capability levels that factories can achieve?

Asked by: Clement B – 5 Sep 2025 10:31

Answer: Routing classes give access to a larger number of manufacturers at the best prices. Every manufacturer has its own limits.

Answered by Christophe LOTZ – 5 Sep 2025 10:34


Question 11: Will the 2212 evolve regularly to take into account manufacturing feedback from boards designed to this spec?

Asked by: Pascal L – 5 Sep 2025 10:34

Answer: answered live

Answered by Christian MAUDET – 5 Sep 2025 10:35

Answer: Yes, that is the principle of a PAS. 3 years to refine it.

Answered by Christophe LOTZ – 5 Sep 2025 11:08


Question 12: I will soon be tackling a board that needs routing, and I would like to use this standard. Do you have a contact at Cadence to try to get this integration as early as possible and spread the word within my company?

Asked by: Tony C – 5 Sep 2025 10:38

Answer: Hello Tony, could you get back to me? I am in charge of getting the 2212 supported by Cadence.

Answered by Christian MAUDET – 5 Sep 2025 10:41


Question 13: Is native integration of the 2212 planned in the Altium tool?

Asked by: Christophe L – 5 Sep 2025 10:40

Answer: See William's presentation, but for my part I have seen nothing on the Altium side since the acquisition by Renesas.

Answered by Christophe LOTZ – 5 Sep 2025 11:06


Question 14: Hello Tony, are the rules available in ALTIUM format?

Asked by: Sébastien B – 5 Sep 2025 10:44

Answer: answered live

Answered by Christian MAUDET – 5 Sep 2025 11:12


Question 15: Hello Christian, yes, I will get back to you and contact you next week about this "SPEC 2212 integration in Allegro" topic. Thank you.

Asked by: Tony C – 5 Sep 2025 10:47

Answer: (no answer recorded)


Question 16: Very good synthesis work, it looks much more digestible and actionable than the IPC standards (2221, 2222…). Do you have a 2212 vs IPC comparison? Even if the approach is different, I imagine that in some cases we will end up with rules that are more or less restrictive depending on the standard used? Put differently: on development projects with China, India, the US… if I use the 2212, do I have an easy way to argue that my design does, or does not, comply with the IPC rules?

Asked by: Romain E – 5 Sep 2025 10:47

Answer: Our DfmExpress tool supports IEC/AFNOR2212 and the IPC standards. It is the best of both worlds.

Answered by Christophe LOTZ – 5 Sep 2025 11:04


Question 17: Thank you for the information

Asked by: Anonymous participant – 5 Sep 2025 10:50

Answer: Thank you for the support

Answered by Christophe LOTZ – 5 Sep 2025 11:04


Question 18: Is integration of the 2212 planned in the Siemens tools (PADS, Xpedition)?

Asked by: Nathan R – 5 Sep 2025 10:50

Answer: Announcements to that effect have been made by Siemens.

Answered by Christophe LOTZ – 5 Sep 2025 11:00


Question 19: Would it be possible to give some clarification on the classes. You explained that these classes are used to set the price of a PCB. For some time now manufacturers have dropped those famous old classes in favor of the IPC ones. I don't really understand the return to classes. Or is it that these classes are only design classes and what drives the price are the IPC classes (1, 2 or 3)

Asked by: Anonymous participant – 5 Sep 2025 10:51

Answer: The routing classes must not be confused with them. Routing classes measure routing complexity, not the target-market classification or reliability. AFNOR Spec 2212 is complementary to the IPC standards.

Answered by Christophe LOTZ – 5 Sep 2025 10:59

Answer: IPC classes 1, 2 and 3 are product classifications:

Answered by Christian MAUDET – 5 Sep 2025 11:00

Answer: IPC classes 1, 2 and 3 are product classifications that affect the price but are independent of the routing classes:
IPC Class 1 products: general-purpose and disposable electronic devices.
IPC Class 2 products: consumer and enhanced professional electronics.
IPC Class 3 products: critical-performance and safety-critical electronics.

Answered by Christian MAUDET – 5 Sep 2025 11:02


Question 20: Hello, is the DFM Express tool free?

Asked by: Anonymous participant – 5 Sep 2025 10:55

Answer: It is a professional tool... so a paid one. Either as a subscription or as a perpetual license. Please contact our sales team through our website.

Answered by Christophe LOTZ – 5 Sep 2025 10:58


Question 21: Can the DfMExpress tool analyze Gerber files rather than the native design data?

Asked by: Mikaël J – 5 Sep 2025 10:55

Answer: An analysis based on Gerber files alone is poorer than an analysis using the native CAD data.

Answered by Christophe LOTZ – 5 Sep 2025 10:57


Question 22: Can this kind of study be subcontracted?

Asked by: Patrice J – 5 Sep 2025 10:56

Answer: Yes, ASTER offers this as a service.

Answered by Christophe LOTZ – 5 Sep 2025 10:56


Question 23: Thank you for this initiative, which was sorely needed. It has always been a real headache.

Asked by: Mickaël B – 5 Sep 2025 10:58

Answer: Thank you. Lots of positive feedback.

Answered by Christophe LOTZ – 5 Sep 2025 11:01


Question 24: Hello, is Altium planning to incorporate the 2212 natively?

Asked by: Jerome V – 5 Sep 2025 10:58

Answer: William's presentation lists the CAD vendors that have started integrating the 2212.

Answered by Christophe LOTZ – 5 Sep 2025 11:00


Question 25: What does the AFNOR Spec bring to DFM beyond what the IPC standards offer?

Asked by: Yohann H – 5 Sep 2025 11:00

Answer: They are complementary. The AFNOR Spec is about being manufacturable by design.

Answered by Christophe LOTZ – 5 Sep 2025 11:01


Question 26: Can the DFM rule library be adapted to match our needs?

Asked by: Erwan R – 5 Sep 2025 11:01

Answer: Yes, our tool is fully programmable and configurable. You can integrate your own rules derived from your field experience.

Answered by Christophe LOTZ – 5 Sep 2025 11:02


Question 27: Hello, how do you keep up with technology developments to keep the manufacturing parameters consistent? As discussed above, classes RC9 and RC10 are technological limits, but a 0.2/0.4 via, for example, ends up in class RC7, which seems high to us since it is fairly standard in Asia.

Asked by: Benoît D – 5 Sep 2025 11:02

Answer: RC9 and RC10 were created to accommodate the future. The IEC/PAS provides for international discussions, with updates to come.

Answered by Christophe LOTZ – 5 Sep 2025 11:03


Question 28: Hello, do you know when integration of the 2212 into Zuken CR8000 is planned? Thank you.

Asked by: BENESCHI D – 5 Sep 2025 11:02

Answer: Work has been announced, but no date that I know of. There will probably be news at the Munich trade show during the week of November 16.

Answered by Christophe LOTZ – 5 Sep 2025 11:05


Question 29: I have to leave, thank you very much for this presentation.

Asked by: Sophie R – 5 Sep 2025 11:06

Answer: answered live

Answered by Christophe LOTZ – 5 Sep 2025 11:07


Question 30: Another question about DFM Express: is it a tool that integrates into the CAD tool, like PCB Flow, or a standalone piece of software? What are the input data for the analyses? Native, ODB, GERBER? Thank you.

Asked by: BENESCHI D – 5 Sep 2025 11:06

Answer: answered live

Answered by Christophe LOTZ – 5 Sep 2025 11:07


Question 31: Why are the dimensions in the Parameters given in mm and not in mils?

Asked by: Sébastien B – 5 Sep 2025 11:08

Answer: Because it is the international unit ... even the IPC standards suggest using mm.

Answered by William MARAIS – 5 Sep 2025 11:13


Question 32: Indeed, back on the 15th, it will be a great pleasure to see you again and to work together!

Asked by: Noémie T – 5 Sep 2025 11:08

Answer: (no answer recorded)


Question 33: Thank you

Asked by: Antony F – 5 Sep 2025 11:08

Answer: (no answer recorded)


Question 34: Thank you very much for this presentation, have a good day.

Asked by: Anonymous participant – 5 Sep 2025 11:09

Answer: (no answer recorded)


Question 35: Thank you very much for all these presentations

Asked by: Jamal R – 5 Sep 2025 11:10

Answer: (no answer recorded)


Question 36: Is the 2212 planned to cover flex circuits?

Asked by: Nathan R – 5 Sep 2025 11:12

Answer: (no answer recorded)


Question 37: Thank you for this webinar! And congratulations on your commitment to the electronics industry

Asked by: Quentin S – 5 Sep 2025 11:14

Answer: (no answer recorded)


Question 38: How can one join the UF91?

Asked by: BENESCHI D – 5 Sep 2025 11:15

Answer: (no answer recorded)


Question 39: Thank you for this excellent, very thorough presentation.

Asked by: Oliviet G – 5 Sep 2025 11:15

Answer: (no answer recorded)


Question 40: Thanks a lot for this webinar.

Asked by: Erwan D – 5 Sep 2025 11:15

Answer: (no answer recorded)